AHG Auto Service » Make » Ford » How do you use a Ford tire sensor tool?

How do you use a Ford tire sensor tool?

To use a Ford tire sensor tool, you will need a TPMS (Tire Pressure Monitoring System) tool specifically designed for Ford vehicles. Here are the general steps to use the tool:
1. Purchase a Ford TPMS tool: You can find Ford TPMS tools online or at automotive stores. Make sure to choose a tool that is compatible with your specific Ford model.
2. Activate the TPMS training mode: Start by turning on the ignition without starting the engine. Locate the TPMS training mode button in your vehicle. The location of this button may vary depending on the Ford model. Refer to your vehicle’s manual or contact a Ford dealership for specific instructions on how to activate the training mode.
3. Use the TPMS tool: Once the training mode is activated, follow the instructions provided with the TPMS tool to program or reprogram the tire sensors. The tool will communicate with the sensors and allow you to reset or relearn them.
4. Complete the training process: After using the TPMS tool, follow any additional instructions provided to complete the training process. This may involve driving the vehicle for a certain distance or at a specific speed to allow the system to recognize the newly programmed sensors.
Please note that the specific steps and procedures may vary depending on the Ford model and the TPMS tool you are using. It is always recommended to consult your vehicle’s manual or contact a Ford dealership for detailed instructions tailored to your specific vehicle.
Source:
– Source: Ford Quick Tips: #47 How To Train Tire Pressure Monitoring Sensors…
– Source: F150 tire sensor relearn procedure using TPMS tool – YouTube
– Source: How to use a TPMS Trainer Tool for Ford Sensors – YouTube

How do I manually reset my Ford TPMS?

And this procedure. Works just fine for that car as it does this car. So this is an automatic ford escape 2013 push button start.

What is a Ford TPMS sensor tool?

A TPMS from one of three manufacturers is fitted as part of the valve assembly in all Ford cars according to the table shown below. The sensor measures the pressure and temperature in the tire and transmits this data along with the unique ID of the TPMS to the tire pressure monitor ECU/receiver.

Do you have to program Ford TPMS sensors?

Every replacement TPMS sensor must be “relearned” to the vehicle following the prescribed OE relearn procedure, regardless of whether it is an OE or aftermarket sensor.

Can you relearn TPMS sensors without a scan tool?

With the exception of some models that may be relearned to the vehicle via a driving procedure, a TPMS scan tool is required to complete the vehicle relearn procedure. Some aftermarket sensors require special programming to meet the vehicle’s application specifications prior to installation and relearn.

What is the magnet for on TPMS tool?

Autel’s TPMS tools can activate sensors and display tire and sensor information. 3. OEM sensors on 2003 and older vehicles, may be activated when a magnet is placed over the sensor valve stem.

How do you relearn a Ford tire sensor?

When the vehicle is off, turn the key to the “On” position, but don’t start the car. Hold down the TPMS reset button until the light blinks three times, then let go. Start the car and give the vehicle about 20 minutes for the sensor to reset. Generally, you’ll find the reset button under the steering wheel.

Can you reset Ford TPMS without tool?

Resetting Your Tire Pressure Light
Attempt to reset the TPMS sensor by driving at least 50 mph for 10 minutes. The next time you turn the car on, the light should be off.

How do you use the Ford TPMS sensor syncing tool?

Now i have to read the instructions. Oh. So now it’s telling us to train or relearn the front left tire. So let’s go over to it with this sensor.

How do you relearn a Ford TPMS sensor?

How to enter the Ford TPMS learning mode?

  1. Make the gear in P position.
  2. Ignition switch to OFF, press and release the brake pedal.
  3. Turn ignition switch from OFF position to RUN position 3 times and nd at RUN position.
  4. Depress and release the brake pedal.
  5. Ignition to OFF position.

How do you use a TPMS sensor tool?

Then you’ll choose the make. You’ll choose the model. And you’ll choose the year of the vehicle that you’re going to be testing a sensor. For once you do that it’ll open up the menu.

AHG Auto Service

At AHG, we are committed to always providing our Perth customers with the best service and benefits when it comes to their vehicle servicing and repair needs. We have over 30 passenger and commercial vehicle dealerships in WA and can handle all of your car servicing needs no matter the make or model.

Leave a Comment